Vaccum cleaner system CV 1004 from Dometic
Powerful, space saving and a very good price / performance ratio.
With the vacuum Cleaner System CV 1004 from Dometic you have a compact device, which finds its place in so many unused spaces and thus does not interfere the space within your vehicle.
With high suction power, the remove even from stubborn dirt in corners and angles is easy and you will come with the 12-meter hose in almost every area of your vehicle. More practically is nearly impossible, and then sweeping make maybe even fun!?!
The device has an additional connection option on the back for a suction hose of around 180 cm in length (included in the scope of delivery). This can be used to position a hose socket (also included in the scope of delivery) in the vehicle at any length in order to reach areas that are too far away from the main device. See also the "Good to know!" section for further information.
Good to know!
The CV 1004 vacuum cleaner is designed so that there are two connections for the actual suction pipe for use in the vehicle:
- via the connection on the front of the main unit and
- via the suction socket located within a radius of approx. 150 cm from the main unit
The extension hose for the suction socket is mounted on the back of the main unit. This basically requires that there is sufficient space for this in a cavity at the back intended to accommodate the main unit (for example a furniture). This cavity should ideally have a depth of at least 30 cm in order to be able to accommodate the main unit (installation depth 15 cm) and the connection sleeve at the back as well as the hose attached to it.
However, the "room" with a slightly lower depth is small, which would at least lead to the extension hose being squashed at some point. However, if the existing depth of the intended cavity is significantly less than 30 cm, the rear connection cannot be made.
In addition to the loss of a second suction pipe connection, this means that the CV 1004 cannot be used in this way without additional on-site measures and without the rear connection hole being covered.
In normal practical cases, the actual suction pipe is plugged into the connection on the front of the device or the suction socket. The suction force generated when the device is switched on seals the connection that is not being used. Its cover is sucked in and thus almost hermetically sealed. The vacuum created in the main device ultimately ensures that the dirt to be picked up is sucked into the corresponding bag. However, if both connections are open, air is sucked in from both at the same time, so that no vacuum (no significant suction power) can be created.
It is therefore essential to seal the rear connection hole hermetically in the long term if the extension hose cannot be used together with the suction socket due to lack of space. However, Dometic has not provided a device or a corresponding component for this purpose to be able to do this if necessary. However, Dometic gives the technical advice of covering the rear connection hole with a suitable, flat plastic plate or similar and additionally sealing it hermetically all around with a sealing compound.
If screwing the cover plate should also be considered for such a measure, then we would like to point out that appropriate holes for the screws should be pre-drilled in order to prevent any stress cracks, particularly in the plastic housing of the main device. The screws intended for use should only have a slightly larger diameter than the hole itself and should only be screwed in by hand and tightened until the sealing compound between the device housing and the cover plate oozes out from under the plate.
Important note on the standard vacuum cleaner bags
Due to the design of the device, the standard vacuum cleaner bags from Dometic for the CV 1004 model have two openings (connection adapter at the front and back). However, if the rear connection cannot be used, then these vacuum cleaner bags are unsuitable for this case, as otherwise the vacuumed dirt will be blown out the back and into the device, which in turn can lead to a defect in the main device.
The previous model CV 1003 from Dometic only had one connection on the front of the device, so its vacuum bag also only has one opening. Dometic still has this vacuum cleaner bag in its range and is listed there under the item number/SKU 910351125. If necessary, you are welcome to ask us about the current availability and price (pack of 5).
Scope of delivery
Included in the delivery are
- 1x Central vacuum cleaner
- 1x Floor nozzle
- 1x Attachment brush
- 1x Dust nozzle
- 1x Crevice nozzle
- 1x Telescopic tube
- 1x Suction hose
- 1x Hose socket
- 2x Screw connector (black)
- 2x Mounting connector (white)
- 1x Connection hose (2 m)
- 2x Dust bag, as well as
- a multi-lingual installation and operating manual
Other accessories are not part of the scope of delivery!
Product safety information
Manufacturer information:
Dometic Germany GmbH
Hollefeldstr. 63
Nordrhein-Westfalen
Emsdetten, Deutschland, 48282
info@dometic-waeco.de
https://www.dometic.com/
Shipping weight: |
8,10 kg
|
Item weight: |
7,20 kg
|
Total measurement: |
298 x 171 x 175 mm (Width x Hight x Depth) |
Input voltage: |
220-240 V~ |
Power consumption: |
950 W |
Current: |
4.5 A |
Suction power: |
2500 mm water column |
Operating temperature: |
-15 °C to +40 °C |
Weight ca.: |
2.7 kg (6.0 lbs) |
Im Lieferumfang enthalten sind
- 1x Zentralstaubsauger
- 1x Bodendüse
- 1x Aufsatzbürste
- 1x Staubdüse
- 1x Fugendüse
- 1x Teleskoprohr
- 1x Saugschlauch
- 1x Schlauchsteckdose
- 2x Schraubverbinder (schwarz)
- 2x Aufsteckverbinder (weiß)
- 1x Verbindungsschlauch (2 m)
- 2x Staubbeutel, als auch
- eine mehrsprachige Montage- und Bedienungsanleitung.
Sonstiges Zubehör ist nicht Bestandteil des Lieferumfangs!
Der Staubsauger CV 1004 ist konstruktiv darauf ausgelegt, dass zu dessen Verwendung im Fahrzeug zwei Anschlüsse für das eigentliche Saugrohr vorhanden sind:
- über den Anschluss auf der Vorderseite des Hauptgerätes und
- über die in einem Radius von ca. 150 cm vom Hauptgerät entfernt platzierte Saugsteckdose
Der Verlängerungsschlauch für die Saugsteckdose wird dabei an der Rückseite des Hauptgerätes montiert. Das setzt grundsätzlich voraus, dass hierfür rückseitig in einem zur Aufnahme des Hauptgerätes vorgesehenen Hohlraum (beispielsweise eines Möbel) ausreichend Platz zur Verfügung steht. Dieser Hohlraum sollte idealerweise eine Tiefe von mindestens 30 cm aufweisen, um das Hauptgerät (Einbautiefe 15 cm) sowie rückseitig die Anschlussmuffe als auch den darauf aufgesteckten Schlauch aufnehmen zu können.
Der "Spielraum" bei etwas geringerer vorhandener Tiefe ist jedoch gering, was zumindest irgendwann zu einem Zusammenquetschen des Verlängerungsschlauches führen würde. Sollte die vorhandene Tiefe des vorgesehenen Hohlraumes jedoch deutlich unterhalb von 30 cm liegen, so wird sich der rückseitige Anschluss nicht herstellen lassen.
Neben dem Verlust eines zweiten Saugrohranschlusses hat das zur Folge, dass der CV 1004 ohne zusätzliche, bauseitige Maßnahme in dieser Art nicht verwendet werden kann, ohne dass die hintere Anschlussbohrung abgedeckt ist.
Im praxistauglichen Normalfall verhält es sich, dass das eigentliche Saugrohr am Anschluss der Gerät-Vorderseite oder dem der Saugsteckdose eingesteckt wird. Die beim Einschalten des Gerätes entstehende Saugkraft dichtet dabei den jeweilig nicht verwendeten Anschluss ab, in dem dessen Deckel angesaugt und somit nahezu Luftdicht verschlossen wird. Das hierdurch im Hauptgerät entstehende Vakuum sorgt letztlich dafür, dass der aufzunehmende Dreck in den entsprechenden Beutel gesaugt wird. Sind beide Anschlüsse jedoch offen, wird aus beiden gleichzeitig Luft angesaugt, so dass kein Vakuum (keine nennenswerte Saugkraft) entstehen kann.
Von daher ist es unabdingbar, die rückseitige Anschlussbohrung auf Dauer luftdicht zu verschließen, sofern der Verlängerungsschlauch zusammen mit der Saugsteckdose mangels Platz nicht verwendet werden kann. Hierfür hat Dometic jedoch keine Vorrichtung oder ein entsprechendes Bauteil vorgesehen, um dies im Bedarfsfall durchführen zu können. Dometic gibt jedoch den technischen Ratschlag, die rückseitige Anschlussöffnung dann beispielsweise mit einer passenden, flachen Kunststoffplatte oder ähnlichem abzudecken und ringsherum zusätzlich mit einer Dichtmasse luftdicht zu verschließen.
Sofern bei einer solchen Maßnahme zusätzlich eine Verschraubung der Abdeckplatte in Erwägung gezogen werden sollte, dann geben wir zu beachten, dass entsprechende Löcher für die Schrauben vorgebohrt werden sollten, um ggf. Spannungsrisse insbesondere im Kunststoffgehäuse des Hauptgerätes zu verhindern. Die zur Verwendung vorgesehenen Schrauben sollten nur einen geringfügig größeren Durchmesser als die Bohrung selbst haben sowie nur mit Handkraft eingeschraubt und soweit angezogen werden, bis die Dichtmasse zwischen Gerätgehäuse und Abdeckplatte unter der Platte hervorquellen wird.
Wichtiger Hinweis zu den serienmäßigen Staubsaugerbeuteln
Die serienmäßigen Staubsaugerbeutel von Dometic für das Modell CV 1004 haben der Konstruktion des Gerätes geschuldet dann auch zwei Öffnungen (Anschlussadapter vorne und hinten). Sollte der hintere Anschluss jedoch nicht genutzt werden können, dann sind diese Staubsaugerbeutel für diesen Fall ungeeignet, da ansonsten der aufgesaugte Schmutz hinten wieder heraus und in das Gerät geblasen wird, was wiederum zu einem Defekt des Hauptgerätes führen kann.
Das Vorgängermodell CV 1003 von Dometic hatte seinerzeit lediglich einen Anschluss an der Vorderseite des Gerätes, so dass auch dessen Saugbeutel nur über eine Öffnung verfügt. Dometic hat diesen Staubsaugerbeutel nach wie vor im Sortiment und wird dort unter der Art.-Nr./SKU 910351125 geführt. Die aktuelle Verfügbarkeit und den Preis (5er Pack) können Sie im Bedarfsfall sehr gerne über uns anfragen.
SHOPVOTE - Bewertungen
There are no product reviews available yet